Frigidaire Oven Error Code F3 in Woodland Hills
F3 on a Frigidaire means the oven temperature sensor circuit is open — the control has lost its thermometer. No reading, no bake: the control shuts the cycle down rather than heat an oven it can't measure.

What error F3 means
Frigidaire's control reads the cavity sensor continuously — about 1,100 ohms at room temperature on a healthy probe. F3 sets when that circuit reads open: the sensor element failed, its wire broke, or a connector let go. It is the electrical twin of a cut phone line — the conversation with the oven's temperature simply stops.
Woodland Hills sits about 5 miles from our Reseda base, well inside our daily Valley loop — we pass through constantly, and same-day visits are straightforward.
How urgent is it? Within the week. Like most sensor codes, F3 is a refusal to bake, not a hazard in progress.
What causes error F3
An error code names the system that reported trouble — the diagnostic finds which of these is yours.
What you can safely check yourself
- Expect a reset to change nothing — open circuits don't heal. One try for the record, then book it.
- Pattern notes help: F3 at the instant you press Bake means the circuit is open cold; F3 twenty minutes into a bake means something separates as it heats — usually a connector or a cracked wire.
- If the range was recently slid out for cleaning or floor work, the sensor plug at the back is suspect number one — mention it.
- The surface burners remain independent on most models; the oven is the grounded section.
What our technician checks
The sensor is metered cold, then the full run — sensor, plug, harness, board pins — is continuity-tested segment by segment, including a heat-and-wiggle pass for the intermittent opens. The failed segment is the repair; nothing else gets replaced on suspicion.
Parts most often involved: oven temperature sensors, sensor harnesses and electronic oven controls. Each is identified against your exact model number.
In Woodland Hills the diagnostic visit is $95 — and nothing is hidden inside it: the technician tests the appliance properly, identifies the failed part by your model number, and quotes one total for the complete repair. Say yes and the diagnostic fee is credited toward the bill. Say no and that's the end of it — just the diagnostic fee, no pressure. The work itself is covered for 1 month on labor and 3 months on parts.
Frigidaire Oven Error Code F3 in Woodland Hills — questions
Is F3 the same on Frigidaire as other brands?
The family resemblance is real — most brands use F3 for a sensor circuit fault — but the exact thresholds and sub-codes are Frigidaire's own. The diagnosis is the same shape: meter the sensor, prove the wire, clear the board.
Can a dirty sensor cause F3?
Dirt doesn't open circuits. Heavy buildup can insulate a sensor and skew readings, but F3 is specifically an electrical open — it ends at a meter, not a cleaning.
Why did F3 appear after I moved the oven?
Because the sensor's plug and harness move with it. A tired connector that was holding on by habit lets go when the range slides — moving day is a classic F3 birthday.
Oven & Range repair in Woodland Hills
This problem in nearby cities
More oven problems in Woodland Hills
Oven & Range error codes in Woodland Hills
Not in Woodland Hills? Read the general guide: Frigidaire Oven Error Code F3 · All appliance problems & error codes · See every city in our service area
Book oven repair in Woodland Hills
Same-day slots fill up by midday. Call or email and we'll lock in your window.
Diagnostic $95 in Woodland Hills — free when you repair with us. Full price in writing before we start. Labor warranty 1 month, parts warranty 3 months.
Book your visit online
Fill in the form, pick a day and an arrival window that work for you — your visit is reserved instantly. Prefer to talk? Call (747) 218-2666.
What will your diagnostic visit cost?
Pick your city and a few details — you see your exact diagnostic price before you book. The full diagnostic fee is credited toward your repair if you proceed with it.