Dryer Won't Shut Off in Azusa

The cycle should have ended an hour ago — the dryer is still tumbling (or still heating). A dryer that won't stop wastes energy at best and cooks clothes and itself at worst.

$95diagnostic in Azusa — free when you repair with us. Full price quoted before we start.
Technician repairing a dryer
What’s broken?
Search our repair videos & guides — e.g. fridge not cooling, dryer noisy

What's going on with your dryer

Sort the complaint first: does it tumble forever without heat, heat without stopping, or simply never advance its timer? Each is a different system — the timer or control that ends cycles, the heating circuit that ignores commands, or the moisture sensor that never declares the load dry. A dryer found still running after a forgotten load is the common discovery story, and the pattern of what's still on (drum? heat? both?) is the map.

Azusa sits about 37 miles from our Reseda base, on the 210-corridor run we drive daily — same-day visits are straightforward.

How urgent is it? Heat-that-won't-stop is urgent — unplug and call. Tumble-forever on timed cycles is an energy and wear problem worth a this-week visit.

What causes dryer won't shut off

Every one of these is found by testing, not guessing — the diagnostic confirms which one you have before any part is quoted.

Timer failed to advanceMechanical timers wear their contacts and motors; electronic controls fail their outputs. The cycle never receives its ending.
Moisture sensor system lying (auto cycles)On auto-dry, the cycle ends when the sensor says 'dry.' Coated sensor bars (dryer-sheet film again) can keep the machine convinced the load is wet for hours.
Heating element grounded (electric)An element shorted to its housing heats whenever the motor runs, regardless of the thermostat — cycles that end with heat that never cycled.
Stuck relay on the control boardA welded relay keeps its circuit powered past the control's intention — heat or motor running on after 'off.'
Door switch confusion on cool-down featuresSome models tumble intermittently after cycles (wrinkle-prevention) — a feature that feels like a fault when it runs longer than expected. Worth ruling out before parts.

What you can safely check yourself

  • Determine what's still on: drum only, heat only, or both — and whether the timer display is advancing at all.
  • Try timed dry instead of auto: if timed cycles end normally, your moisture sensor system is the story.
  • Clean the moisture sensor bars inside the drum (two metal strips near the lint filter) with a cloth and a little rubbing alcohol — film on them is the classic auto-cycle liar.
  • If the heat stays on with the dryer 'off,' unplug it and call promptly — a machine heating uncommanded is not a wait-and-see appliance.

What our technician checks

Cycle control is tested at its outputs: timer advance verified, board relays checked for welded contacts, element tested for grounds, moisture-sensor circuit measured with wet and dry loads simulated. The fault is found in the system that's actually misbehaving — timer, sensor, or power circuit — rather than the system that merely looks guilty.

Parts most often involved in this repair: timers, control boards and relays, moisture sensors, heating elements. Each is identified against your exact model number — no universal substitutes.

$95diagnostic visit in Azusa — free when you repair with us
1 mo / 3 molabor warranty / parts warranty on every repair
≈37 mifrom our Reseda base — Azusa is regular route coverage

In Azusa the diagnostic visit is $95 — and nothing is hidden inside it: the technician tests the appliance properly, identifies the failed part by your model number, and quotes one total for the complete repair. Say yes and the diagnostic fee is credited toward the bill. Say no and that's the end of it — just the diagnostic fee, no pressure. The work itself is covered for 1 month on labor and 3 months on parts.

Dryer Won't Shut Off in Azusa — questions

Why does my dryer run for hours on auto dry?

Because the moisture sensor never gets to declare the load dry — usually because its bars are filmed with softener residue, sometimes because the sensor circuit has failed. Timed dry bypasses the liar.

Why is my dryer still hot after the cycle ended?

Residual heat is normal for a few minutes. A dryer actively heating after 'off' suggests a grounded element or welded relay — that's an unplug-and-call, not a quirk.

Can a dryer really run all night?

Yes — a failed timer or control won't stop it, and it'll tumble (and possibly heat) until it's stopped manually or something else fails. Found one running in the morning? Get it checked before its next load.

Book dryer repair in Azusa

Same-day slots fill up by midday. Call or email and we'll lock in your window.

Diagnostic $95 in Azusa — free when you repair with us. Full price in writing before we start. Labor warranty 1 month, parts warranty 3 months.

Book your visit online

Fill in the form, pick a day and an arrival window that work for you — your visit is reserved instantly. Prefer to talk? Call (747) 218-2666.

What will your diagnostic visit cost?

Pick your city and a few details — you see your exact diagnostic price before you book. The full diagnostic fee is credited toward your repair if you proceed with it.

Please review our service call terms:

• The diagnostic visit is $95 in most of our service area and $125 in Calabasas, Encino, Sherman Oaks and Arcadia. If you proceed with the repair, the full diagnostic fee is credited toward your repair — you pay only for the repair itself. If you decide not to repair, the diagnostic fee is due for the visit.

• Built-in and stacked units: in most cases (about 60%) we can diagnose a built-in unit in place. Sometimes a full diagnosis requires pulling the unit out (extraction), or removing a dryer stacked on top of a washer. Extraction is done only with your approval on site and costs extra, in addition to the diagnostic fee: removing a stacked dryer — $150; single built-in oven — $250; double built-in oven — $300; built-in refrigerator — from $600 (the exact price depends on the model and the access, and is quoted on site before any work begins). You may decline extraction and end the visit at any point — then only the diagnostic fee applies, even if a complete diagnosis is not possible without extraction.

• Confirming your visit: before heading out, your technician will text you to confirm. Please reply — if we don't receive a reply, your reserved slot will be released and the visit cancelled. If you need to cancel, please let us know before the technician heads out; once the technician has arrived, the diagnostic fee applies.

Please scroll the terms to the end to continue.

Call now Book a visit Diagnostic cost